Right click the adapter and select properties. On the Network Connections screen select Local Area Connection with the type of Microsoft Loopback Adapter. Click the Change adapter settings on the left hand side of the panel. In the Control Panel open the Network and Sharing Center. Once the installation is complete click the Finish button to exit the Add Hardware Wizard. On the confirmation screen click the Next button to install the Microsoft Loopback Adapter. On the Select Network Adapter screen select Microsoft for the Manufacturer and select Microsoft Loopback Adapter for the Network Adapter. Scroll down and select Network adapters and click the Next button. Select the “Instal the hardware that I manually select from a list (Advanced)” and click the Next button to continue. Run the Command Prompt using Run As Administrator and enter hdwwiz.exe to start the Add Hardware Wizard. This document will detail the setup and configuration on Windows hosts in particular this install was done on Windows 7 Ultimate. You can prevent this issue by configuring the Loopback Adpater on your DHCP machine prior to installing Oracle products. Many Oracle products such as Database Control, Database Listener, Weblogic Server either standalone or bundled in JDeveloper use the machine IP address and or host name during the installation and may fail to function properly when either changes. In our case 192.168.1.253 DEV-WriteBackSC.One of the most missed configuration issue when installing Oracle Database on Windows systems is failure to configure the Loopback adapter prior to installing the software on DHCP clients. You have to do the following: Open your windows\system32\drivers\etc\ folder, open the hosts file with Notepad and add an entry for your static IP. Finally, modify your hosts file to associate your static IP address with your computer name. Image 10: Network connection Advanced settingsĥ. Make sure your loopback adapter network connection is at the top of the Connections list (use the up/down arrows if not). From Network Connections, click Advanced, and select Advanced Settings from the menu. Image 9: Loopback adapter Connection DNS configurationĤ. The subnet mask and the default gateway need to be introduced as well. There you type in the static IP that the ClearPeaks network administrator has assigned you (in our case 192.169.1.63). Here, you select Internet Protocol (TCP/IP) and click on the Properties button. Now, let’s right click on the original network connection and select properties. Image 8: Loopback adapter Connection IP address configurationģ. Then click OK and close the properties window. From the properties screen for TCP/IP, select ‘ Use the following IP address’ and fill in a loopback IP address (make sure to pick something not within your current subnet!). Image 7: Network connections List / Loopback adapter Connection TCP / IP settingsĢ. Open the Network Connections list, right click on the new network connection (it’s suggested to rename it to Loopback Adapter Connection before) and select properties. To properly configure the loopback adapter you need to go through the following steps:ġ. This will add the Microsoft Loopback Adapter as a new Local Area Connection in your Network Connections list. You’ll need to click next a few more times, then finish. Select ‘ Microsoft’ as the manufacturer, and ‘ Microsoft Loopback Adapter’ as the Network Adapter.ħ. Select ‘ Network Adapters’ from device types.Ħ. Select ‘ Install the hardware that I manually select from a list’, and click next.ĥ. Select Next to skip over the first two screens, then select ‘ Yes, I have already added hardware’ and select next again.ģ. Scroll to the bottom of the list on the following screen, and select the ‘ Add a new hardware device’ option, click next again.Ĥ. In order to install the loopback adapter in the Windows 2003 Virtual Machine, you need to:ġ. Go through the ‘ Add Hardware’ wizard (from the control panel).Ģ. In fact, Business Intelligence installation will fail for the mentioned environments if the loopback adapter is not properly configured. Having the loopback adapter set up is required before installing OBIEE 11g. The aim of this document is to provide a guide that thoroughly explains the steps of creating and configuring a Loopback Adapter.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |